- PLANEPLOTTER WITH PIAWARE MAC OS
- PLANEPLOTTER WITH PIAWARE SERIAL
- PLANEPLOTTER WITH PIAWARE FULL
- PLANEPLOTTER WITH PIAWARE PRO
- PLANEPLOTTER WITH PIAWARE PASSWORD
The basic flow of the new Piaware MLAT system is here: That setup is working very well, feeding data to the PlanePlotter servers via modesmixer2 and ppup1090 on port 30005.
PLANEPLOTTER WITH PIAWARE SERIAL
# can be provided set "wireless-type" to static to use this.Piaware has recently added the capability of doing MLAT processing, I decided to see if I could get this working with my modesmixer2 setup that is receiving serial over USB data from a Mode-S Beast receiver rather than than a dongle using dump1090.
PLANEPLOTTER WITH PIAWARE PASSWORD
Wireless-password s3cr3t <-replace s3cr3t with the password to your WiFi Wireless-ssid MyWifiNetwork <-replace MyWifiNetwork with the name of your WiFi (aka the SSID of your local network) # network SSID and, for networks that require # This should be changed to match your wireless # a supported USB wifi adaptor for this to work. # for network access? You will need to attach # can be provided set "wired-type" to static to use this. # Alternatively, a static address configuration # Should piaware use the wired ethernet port # All other lines specify configuration settings. # Lines beginning with a '#' are comment lines # file is read and its contents are used to # This file configures the Piaware sdcard image Open the file labeled piaware-config.txtīelow is the text file opened, instructions to enable Wi-Fi are in BOLD.Select the Micro SD card device labeled piaware.All other lines specify configuration settings. Lines beginning with a “#” are comment lines and are ignored.
PLANEPLOTTER WITH PIAWARE MAC OS
The TextEdit program on a MAC OS is known for saving in the rich text format and smart quotes so be sure those options are disabled in the program's preferences. The configuration file is a simple plain text format file.
PLANEPLOTTER WITH PIAWARE FULL
For full configuration options see advanced configuration Configuration File Format * indicates a setting that can be configured on the site's statistics page. Receiver type (RTL-SDR, Beast, Radarcape or other Mode S/ADS-B source).PiAware supports unencrypted networks or WPA/WPA2 encrypted networks WEP is not supported.The configuration file allows the user to configure and set the following Etcher will automatically eject the Micro SD card after formatting, physically remove the Micro SD card or USB adapter and plug it back into the computer to edit the configuration file. If on board Wi-Fi or a USB adapter will be used to connect to the internet you will need to edit the configuration file. Indoor/Outdoor 978 MHz UAT Antenna with mounting bracket (FlightAware Store).
PLANEPLOTTER WITH PIAWARE PRO
FlightAware Pro Stick USB ADS-B Receiver + Cable + Filter + Antenna (eBay).Indoor/Outdoor 1090MHz ADS-B Antenna with mounting bracket (FlightAware Store).Indoor Antenna MCX plug with a SMA adapter (eBay).FlightAware Pro Stick USB ADS-B Receiver (FlightAware Store).Power Supply for Raspberry Pi (Raspberry Pi).Raspberry Pi 3/4/Zero Computer (Raspberry Pi).If you are in an area known for high voltage spikes consider an 800 joules surge protector.The Raspberry Pi is vulnerable to voltage spikes so consider a surge protector to prevent damage.If you live in an urban environment or a location that has a lot of radio noise this will help filter out that excess signal.Skip the step to program the micro SD card.If you use a telescoping mast antenna be sure to collapse it to a quarter wavelength of 1090 MHz (6.9 cm) to maximize reception.Īdditionally, you can choose to purchase or find the following items but they are not required.If using the FlightAware USB adapter be sure the antenna has an SMA connector. An indoor antenna can be purchased to start.Hint: If you are choosing between the FlightAware Pro Stick and the Pro Stick Plus remember the Plus has an on-board filter that works well in locations that have a lot of radio noise, such as urban environments.The USB SDR (Software Defined Radio) ADS-B (Automatic Dependent Surveillance-Broadcast) receiver translates the 1090 MHz radio signal into something the computer can understand.USB SDR ADS-B Receiver (FlightAware Pro Stick or Pro Stick Plus recommended).If your computer does not have a built-in SD card reader/writer, you will need the optional USB SD card reader/writer.5.1 Volts 2.5 Amps power supply recommended.To build a PiAware, you must obtain the following components:
0 kommentar(er)
